TY - GEN
T1 - Mechanically milled al base MMC reinforced with Ti3Al intermetallics
AU - Adamiak, M.
PY - 2007
Y1 - 2007
N2 - The present work investigates the structure and selected properties of the aluminum AA 6061 matrix composite materials reinforced with Ti3Al intermetallic particles. The composites were produced by powder metallurgy techniques followed by hot extrusion. The introduction of new reinforcements continues to be investigated in order to improve final behavior of AMCs as well as to avoid some drawbacks of using ceramics as reinforcements. As it is well known that mechanical milling improve characteristics of treated materials, to evaluate the effect of mechanical milling two types of ball mills were used: a low energy (horizontal ball mill) and a high energy one (eccentric ball mill). Basing on the investigations carried out, it was found out that the milling process has a big influence on the characteristics of powder materials, changing their morphology by repeated welding-fracture welding, finally allowing to produce composite particles. The investigation carried out shows that so called brittle intermetallic particles yields to plastic deformation and in the contrary to ceramic particles can not play a role of the accelerator during mechanical milling. The mechanically milled and extruded composites show better mechanical properties of obtained products because of finer and better distribution of reinforcement particles as well as because of the high degree of stress accumulated by plastic deformation. In comparison to composites produced without mechanical milling the hardness increases twice in case of mechanically milled composites. Higher reinforcement content results in higher particles dispersion hardening, for 15 wt. % of intermetallics reinforcement concentration composites reach about 400 MPa UTS. Results of investigation of joints carried out show that the best mechanical properties of joints can be achieved by applying soft conditions of butt welding process e.g. current 1300 A and current flow time 1,2 s. To improve hardness and tensile properties of butt welding joints age hardening is necessary.
AB - The present work investigates the structure and selected properties of the aluminum AA 6061 matrix composite materials reinforced with Ti3Al intermetallic particles. The composites were produced by powder metallurgy techniques followed by hot extrusion. The introduction of new reinforcements continues to be investigated in order to improve final behavior of AMCs as well as to avoid some drawbacks of using ceramics as reinforcements. As it is well known that mechanical milling improve characteristics of treated materials, to evaluate the effect of mechanical milling two types of ball mills were used: a low energy (horizontal ball mill) and a high energy one (eccentric ball mill). Basing on the investigations carried out, it was found out that the milling process has a big influence on the characteristics of powder materials, changing their morphology by repeated welding-fracture welding, finally allowing to produce composite particles. The investigation carried out shows that so called brittle intermetallic particles yields to plastic deformation and in the contrary to ceramic particles can not play a role of the accelerator during mechanical milling. The mechanically milled and extruded composites show better mechanical properties of obtained products because of finer and better distribution of reinforcement particles as well as because of the high degree of stress accumulated by plastic deformation. In comparison to composites produced without mechanical milling the hardness increases twice in case of mechanically milled composites. Higher reinforcement content results in higher particles dispersion hardening, for 15 wt. % of intermetallics reinforcement concentration composites reach about 400 MPa UTS. Results of investigation of joints carried out show that the best mechanical properties of joints can be achieved by applying soft conditions of butt welding process e.g. current 1300 A and current flow time 1,2 s. To improve hardness and tensile properties of butt welding joints age hardening is necessary.
KW - AMCs
KW - Aluminum matrix composites -
KW - Intermetallic
KW - Mechanical milling
KW - Powder metallurgy
KW - TiAl
UR - https://www.scopus.com/pages/publications/58349096113
M3 - Conference contribution
AN - SCOPUS:58349096113
SN - 9781605601335
T3 - Materials Science and Technology Conference and Exhibition, MS and T'07 - "Exploring Structure, Processing, and Applications Across Multiple Materials Systems"
SP - 2005
EP - 2016
BT - Materials Science and Technology Conference and Exhibition, MS and T'07 - "Exploring Structure, Processing, and Applications Across Multiple Materials Systems"
PB - Materials Science and Technology
T2 - Materials Science and Technology Conference and Exhibition, MS and T'07 - "Exploring Structure, Processing, and Applications Across Multiple Materials Systems"
Y2 - 16 September 2007 through 20 September 2007
ER -